OBD2 TO USB ELM327 CABLE SCAN TOOL (CAOBD2USB)

  • $44.95
Tax included.


Our OBD-AUS ELM327 OBD2 USB scanner cable is a diagnostic scanner for both automotive enthusiasts and professionals. It features an integrated original microchip PIC18F25K80 and FTDI FT232RL Serial to USB Chip and is compatible with a ride range of operating systems including Windows, Mac OSX, Linux and also Android devices using an USB OTG adapter cable.

  • Genuine FTDI FT232RL Chip
  • Genuine Microchip PIC18F25K80 Microcontroller
  • 1.5m Cable length so you can reach where you need.
  • Read and erase diagnostic trouble codes (DTCs) and turn off the check engine light
  • View real-time vehicle data, graphs and performance parameters
  • Find and fix problems before they happen
  • Compatible with all OBDII compliant vehicles
  • Compatible with Android devices using an USB OTG adapter cable
Paired with one of the many compatible diagnostic software or application, the OBD2 USB Cable allows you to easily scan and clear engine codes, view and record real-time engine and performance data, view emissions status and much more.

It features a stable, high quality, genuine Microchip PIC18F25K80 micro-controller which adds key features such as automatic protocol search and identification and low power consumption.

Multi-Protocol Support:  

  • ISO 9141-2 (5 baud init, 10.4 kbaud)
  • ISO 14230-4 KWP (5 baud init, 10.4 kbaud) (KWP2000)
  • ISO 14230-4 KWP (fast init, 10.4 kbaud) (KWP2000)
  • ISO 15765-4 CAN (11 bit ID, 500 kbaud)
  • ISO 15765-4 CAN (29 bit ID, 500 kbaud)
  • ISO 15765-4 CAN (11 bit ID, 250 kbaud)
  • ISO 15765-4 CAN (29 bit ID, 250 kbaud)
  • SAE J1850 PWM (Older Ford vehicles)
  • SAE J1850 VPW (Older GM vehicles)

Vehicle Coverage:

Works on all OBDII Vehicles (1996+ in USA) and EOBD vehicles.
For your vehicle to be OBDII compliant it must have a 16-pin DLC (Data Link Connector) under the dash and the Vehicle Emission Control Information Label must state that the vehicle is OBD II compliant

With the appropriate diagnostics software or application, the ELM327 USB can perform the following operations:

  • Read diagnostic trouble codes, both generic and manufacturer-specific, and display code descriptions with over 3000 universal code definitions in the database
  • Clear diagnostic trouble codes and turn off check engine lights
  • Display and record real-time sensor data, including:
    Engine RPM
    Coolant Temperature
    Calculated Load Value
    Fuel System Status
    MPH Speed
    Short Term Fuel Trim
    Long Term Fuel Trim
    Intake Manifold Pressure
    Timing Advance
    Intake Air Temperature
    Air Flow Rate
    Absolute Throttle Position
    Oxygen Sensor Voltages/Associated Short Term Fuel Trims
    Fuel System Status
    Fuel Pressure
    + More
Automatically searches for the correct protocol or can be configured manually.

Status LED

Length with USB Lead : 1.5 metres

RS232 baud rates to 500 Kbps

Adaptive Timing automatically adjusts ST timeouts

Power up to AT MA is selectable

Source (tester) address can be changed

Can reset all PPs with a jumper

Receive addresses can be independently set

Power Control with a low power standby mode

A 4800 baud ISO option

A non-volatile memory location for storing user data

CAN extended addressing support

You can now perform ISO/KWP bus initialisations without having to send a request

An SS command allows searching through the OBD protocols sequentially

A new TA command allows the Tester Address to be easily changed

Factory calibration for the voltage reading circuit can be easily restored

ISO 9141 and ISO 14230:

The slow initiation address can now be varied

Control over key word checking

KWP protocols can now transmit 3 or 4 byte headers




Specifications:

Connection: USB 2.0/1.1
Baud Rate: 9600 or 38400
Indicator LEDs: OBD Tx/Rx , RS232 Tx/Rx , Power
Voltage: 12V
USB to Serial Chip: FTDI FT232RL USB to UART
Firmware Version: 1.5

Microchip PIC18F25K80 Specifications:

Program memory: 32K Flash
CPU Speed: 16 MIPS
RAM: 3,648 bytes
Data EEPROM: 1024 bypes
ADC (Analog to Digital Converter): 8 ch, 12-bit
Comparators: 2

 CAOBD2USB


We Also Recommend